Black Double Wall Stove Pipe - Red Hill General Store
Call to order toll free 1-800-251-8824
Shopping Cart

Black 6 inch Selkirk DSP Double Wall Stove Pipe

Selkirk's DSP Double Wall Stove Pipe is a connector pipe that links your wood stove to an insulated chimney. Listed & Tested to ULC S641 and UL 103 Standards. Model DSP has an attractive outer black surface made of durable aluminized steel to withstand temperatures up to 1200 degrees F in continuous operation. Double Wall construction with a 1/4” air space between inner and outer pipes provides a superior insulating value than single wall pipe. Better insulating value keeps flue gas temperatures higher. This helps your Woodstove perform with an enhanced draft, which provides: Less chance of moisture or soot build up within the vent, Reduced “smoking” of the Stove at start up, Increased efficiency, Less creosote build up. Double Wall Stove Pipe not only keeps the flue temperatures higher, it also keeps the outer pipe temperatures cooler. This allows Double Wall Stove Pipe to be installed with only 6” of clearance to combustible materials. Single Wall Stove Pipe requires an 18” clearance, which typically means your Wood Stove sits further away from the wall and takes up valuable space within the room. The inner liner of Model DSP is made from corrosion resistant 400 series Stainless Steel. Model DSP is available in a variety of lengths and elbows for ease of installation. Telescopic and Adjustable Lengths are available to eliminate cutting-to-size and allows access to the system for cleaning and inspection. The black finish of Model DSP provides a very rich and distinguished appearance. Black enamel paint is used to provide a long lasting, brighter finish that also resists scratches. Please note: Double Wall Stove Pipe cannot be cut and still provide a proper connection to an adjoining piece of pipe. If necessary use an adjustable length of double wall stove pipe.

Lasts significantly longer than single wall stove pipe
Only 6” Clearance to combustible materials
Stainless Steel inner liner
Aluminized Steel outer casing
1/4” air insulation
Black enamel finish
Easy to install

This item is not available for our Ship to Store Service
Order Item
12" Straight Pipe
6" x 12"
Ocp77310
$89.49
5.95 lbs
Add to Cart
24" Straight Pipe
6" x 24"
Ocp77315
$139.49
8.6 lbs
Add to Cart
36" Straight Pipe
6" x 36"
Ocp77320
$165.49
12.5 lbs
Add to Cart
45 Degree Elbow
6"
Ocp77345
$106.49
5.4 lbs
Add to Cart
6" Straight Pipe
6" x 6"
Ocp77305
$63.99
4.85 lbs
Add to Cart
90 Degree Elbow
6"
Ocp77350
$151.99
7 lbs
Add to Cart
Damper Kit
6"
Ocp77340
$106.49
5.01 lbs
Add to Cart
Finishing Band
3" High
Ocp77375
$23.99
5 lbs
Add to Cart
Increaser
6" to 8"
Ocp77370
$155.49
6.41 lbs
Add to Cart
Masonry Adaptor
6"
Ocp77355
$85.99
5.68 lbs
Add to Cart
Stove Adaptor
6"
Ocp77360
$68.99
7 lbs
Add to Cart
Tee With Cap
6"
Ocp77335
$136.99
8 lbs
Add to Cart
Adjustable Length
12"-18"
Ocp77325
$113.99
7.95 lbs
Add to Cart
Telescoping Length
38"-68"
Ocp77330
$290.49
24 lbs
Add to Cart

Black 6 inch Selkirk DSP Double Wall Stove Pipe

Selkirk DSP

Description of available pieces
Straight Pipe -
3 metal screws supplied with each Length. For Installed Length, subtract 1-3/8" per joint.
45 degree Elbow - Offsets obstructions as needed. Non-adjustable.
90 degree Elbow - Offsets obstructions as needed. Non-adjustable. Not recommended for rear exit appliances.
Stovetop Adaptor - May be required to adapt some stove flue outlets to Double Wall Stove Pipe.
Tee with Cap - Used in conjunction with a vertical insulated chimney to provide easy access for
inspection and cleaning.
Adjustable Length - Includes Finishing Band. Used to adjust pipe to desired length. Eliminates the need to cut pipe. For Installed Length, subtract 1-3/8" per joint.
Telescoping Length - Includes Finishing Band. Easily removable for inspection and cleaning. Eliminates the need to cut pipe. For Installed Length, subtract 1-3/8" per joint.
Masonry Adaptor - For installations through a masonry wall. Used to connect Double Wall Stove Pipe to an existing masonry chimney or a relined masonry chimney with stainless steel liner.
Damper Kit - Allows the operator to alter the amount of air drawn through the venting system, controlling the stove’s combustion. Must be installed directly on the stove’s flue outlet where applicable. When handle is in horizontal position, the damper is “closed” (reducing combustion). The “closed” position is still 20% open, so the venting system is not completely blocked. When handle is in vertical position, the damper is wide open (no reduction of combustion).
Increaser - Used to increase the size of the pipe to the chimney.
Finishing Band - Used to conceal the crimped end on the last length in the system. When installing, the joints appear to be going the wrong direction with a “male-end-up” connection (this is correct for the outer wall). The finishing band conceals the joints and provides a finished look.
Spacer Line
Frequently asked questions about Stove Pipe

Please note: For safety considerations and ease of installation follow these guidelines.
1. Never mix and match gauges of stove pipe.
2. Use a stove pipe reducer or increaser if you are working with different sizes of pipe.
3. Buy all of the pipe you need from one brand. The connection will most likely differ from Brand X to Brand Y.
4. While all of the stove pipe we sell will fit together tightly a very secure connection can be obtained by using 3 screws per connection. Screws also make the entire assembly stronger.
5. New stove pipe may smoke a little and emit an odor when first used. This is normal and nothing to be concerned about. It is simply the paint on the pipe curing a bit. If necessary open a window or door to allow the smoke and fumes to escape.
Return to top of page

Spacer Line
Find us on Twitter Follow us on Facebook Read our Red Hill General Store Blog Visit our Channel on Youtube Secure Ordering Privacy Policy Black 6 inch Selkirk DSP Double Wall Stove Pipe